|
|
| XIM 400 and 400W are fast drying solvent based Bonders as
well as Primer/Sealers developed to solve many painting problems. They provide
excellent sealing and adhesion to many hard-to-coat surfaces. 400W is
recognized as a leading bonding primer for tough-to-coat surfaces by major
painting contractors. |
 |
These Bonders are an ideal prime coat for Wood,
Ferrous Metals and Non-Ferrous Metals, Plaster, Formica, Some plastics, Glass,
Tile, Fiberglass, Hardboard, etc. Because there are many types of surfaces,
plastics, and composite materials, always test a small area first for adhesion
and topcoat compatibility. On extremely porous surfaces or severe staining
types of wood a second coat of 400W may be needed prior to applying the coat.
Not recommended for tubs, sinks or showers where continuous water or
hot water contact occurs. Not recommended for use on Polyethylene, Kynar,
Teflon or Nylon. |
| Potential Applications: Building material
Plastic: including PVC sheeting and piping, vinyl molding and mill work,
laminated Formica paneling and cabinets as well as fiberglass garage doors and
other molded parts. First, remove old and loose paint then clean away wax,
polish, grease, oil and other contaminants from the surface with a strong
abrasive detergent. Wipe the surface with a cleaning solvent such as XIM GON
Cleaner or xylene. Dry, then scuff sand the surface for maximum adhesion. Apply
the XIM Bonder, wait 1-2 hours and topcoat. Tile, Glazed Block and brick,
Porcelain: Decorative surfaces such as these can be restored and painted.
First, remove old paint and debris. Repair or patch any broken or damaged
areas. Then clean away any wax, polish, grease, oil and other contaminants with
a strong abrasive detergent. Wipe the surface with a cleaning solvent such as
XIM GON Cleaner or xylene. Scuff sand for maximum adhesion. Apply the XIM
Bonder and allow to dry for 1-2 hours then apply the topcoat. Not recommended
for sinks, tubs, or shower areas where continuous water or hot water can be
present. Note: Where flexible seams or soft caulking is present, do not paint
over with the 400 W. Use a softer primer for these areas. Always plan your job
ahead and caulk after painting. Always caulk edges or seams that can trap and
hold moisture and become source of coating failure. |
|
|
|
|
|
|
Potential Applications: Building Material
Plastic: More and more plastics are used in the building industry, including
PVC sheeting and piping, vinyl shutters, vinyl molding and mill work, laminated
Formica paneling and cabinets as well as fiberglass garage doors and other
molded parts. First, remove old and loose paint then clean away wax, polish,
grease, oil and other contaminants from the surface with a strong abrasive
detergent. Wipe the surface with a cleaning solvent such as XIM GON Cleaner or
xylene. Dry, then scuff sand the surface for maximum adhesion. Apply the XIM
Bonder. wait 3 hours and topcoat. Test for adhesion before starting the job.
Advanced Technology UMA is recommended for priming Kynar and Silicone Polyester
precoated siding. When priming Kynar and Silicone Polyester pre-painted siding
at least two test patches in different areas is a must to demonstrate adhesion
that is acceptable to you. Tile. Glazed Block and Brick, Porcelain: Decorative
surfaces such as these can be restored and painted. First remove old paint and
debris. Repair or patch any broken or damaged areas. Then clean away any wax,
polish, grease, oil and other contaminants with a strong abrasive detergent.
Wipe the surface with a cleaning solvent such as XIM GON Cleaner or xylene. For
maximum adhesion scuff sand or etch the surface with XIM's etching cream,
EtchIM, rinse well to remove any etching residues and allow to dry. Apply the
UMA Bonder and allow to dry for 3 hours then apply the
topcoat.
NonFerrous Metals: With XIM Advanced Technology UMA brand
Bonder you can get a long lasting, durable job when painting aluminum doors and
window frames, aluminum and copper flashing and trim as well as galvanized
steel. Clean away all corrosion and any old paint, dirt, wax and grease. Wipe
the surface with a cleaning solvent such as XIM's GON Prep cleaner. Allow to
dry, then apply the UMA Bonder (only one coat is required). Allow the UMA to
dry for three hours, then apply the top coat.
|
Not recommended for sinks, tubs or shower areas where
continuous water or hot water can be present. Note: where flexible seams or
soft caulking are present, do not paint over with the UMA. Always plan your job
ahead and caulk after painting. Always caulk edges or seams that can trap and
hold moisture and become the source of coating failure.
For exterior
jobs where high water contact is expected or where moisture or dew may
accumulate, two coats of the top coat paint are recommended. |
|
|
|
|
|
| XIM PEELBOND (tm) is a unique Water Based, Clear Bonder /
Sealer. It is formulated to bond and seal a wide range of construction
surfaces. It bonds paint and will stay flexible over the life of the paint. It
has excellent filling and sealing properties and can help reduce cracking and
peeling. Interior or Exterior application. |
 |
| Applications: For Sealing: Wood, Hardboard, Plywood, T111
Siding, Masonite, Wallboard, Stucco, Brick Features/Benefits: Excellent
Adhesion, Fast Drying, Penetrates Into Wood, Bridges Low Areas In One Pass,
Bonds To Old But Sound Surfaces, Water Based, Soap and Water Clean Up |
|
|
|
